 |
|
| Products - New products in addition to these are in production with a scheduled release date of July 15th, 2007
|
 |
| Ultra-8 Display |
 |
|
|
The Ultra-8 display panel is our newest and most feature rich display. This panel can be used to monitor up to 8 tanks. It displays tank levels in 10% increments on an easy to read 16x2 LCD display. This unit is also easy to setup and adjust with onscreen instructions.
|
|
|
|
Ever forget to check your tanks and had one go dry or overfill? The Ultra-8 panel remembers for you. Every 2 hours it reads the levels for all attached tanks. If a waste tank is getting too high, or if a fresh tank is getting too low, then the Ultra-8 beeps a warning (except at night) and lights a warning light to alert the owner to check their tanks.
|
|
|
|
Overall Panel Dimensions: 3 3/16 x 7 inches.
| |
|
|
Retail Price $150.00 plus $35.00 per tank for each sensor.
Example - 5 tanks would be $175.00 for sensors and $150.00 for monitor for a total of $325.00.
|
|
|
|
|
| Smart Mini |
 |
|
|
The Mini-Panel display is the smallest display panel we manufacture. This panel is used when there is only a single tank to monitor. It displays the tank levels in quarters (E, 1/4, 1/2, 3/4, & F) with a series of LEDs.
|
|
|
|
Our one tank unit has become pot(less) through the use of our new Smart Chip technology. Only a button push at empty and full is required to accurately calibrate your tank.
|
|
|
|
Overall Panel Dimensions: 2 x 3.5 inches.
| |
|
|
|
| LED-Smart 3 Tank |
 |
|
|
The LED-Smart 3 Tank display panel is used to monitor up to 3 separate tanks. It displays the tank levels in quarters (E, 1/4, 1/2, 3/4, & F) with a series of LEDs.
|
|
|
|
This panel is also pot(less) through the use of our new Smart Chip technology. Only a button push at empty and full is required to accurately calibrate your tank.
|
|
|
|
This panel comes either as a 12V version which takes power directly from your RV, or as a 9V version that has it's own battery.
|
|
|
|
Overall Panel Dimensions: 2.75 x 5.25 inches.
| |
|
|
|
| MODA Tank Sensor |
 |
|
|
The MODA sensor module is a non-invasive fresh and waste tank level sensor. This sensor is attached to the outside of a plastic or fiberglass tank eliminating the possibility of sensor malfunction due to fouling by tank contents.
|
|
|
|
Due to its non-invasive nature, the MODA sensor module is simple to install. It is installed by applying 2 vertical strips of aluminum tape to the side of the tank, then sticking the MODA copper patches over them. Installation is completed by sticking the module itself to the tank then extending its wires to the display.
|
|
|
|
This sensor is compatible with all of our RV and Marine display panels for tank of 30 inches or less in depth.
|
|
|
|
|
| AutoCal Tank Sensor |
 |
|
|
The AutoCal sensor module is another non-invasive fresh and waste tank level sensor.
|
|
|
|
In addition to features of the MODA sensor module, the AutoCal module allows the user to calibrate sensor for full and empty tank levels. With exception to the simple calibration proceedure, this module installs in an identical fashion to the MODA sensor module.
|
|
|
|
This sensor is compatible with all of our RV and Marine display panels for tanks from 30 to 60 inches in depth.
|
|
|
|
|
| Diesel Fuel Sensor |
 |
|
|
This sensor was developed to incorporate fuel tank monitoring with our existing tank monitoring systems.
|
|
|
|
This unit installs into a SAE standard 5 hole fuel sender opening in the fuel tank. A BUNA-N gasket and 5 stainless steel screws are included with the sensor. These sensors are custom made to the length specified by the customer at time of order (from 6" to 70"), and the unit is factory calibrated. The sensor head is 2.75" by 0.75" in size and requires about an inch of clearance (measured from the top of the tank) to install.
|
|
|
|
This sensor is compatible with all of our RV and Marine display panels.
|
|
|
|
|
| PVC Rod Sensors |
 |
|
|
In cases where there is no access to the sides of a plastic water or waste tank to apply the aluminum tape required by the MODA or AutoCal sensor modules, or in the event that the tank to be monitored is constructed of metal, a PVC rod-style sensor can be used.
|
|
|
|
These sensors install into a 1 inch (NPT) threaded hole in the top of the tank. About an inch of clearance 1 1/4 " above the female threads (measured from the top of the tank) is required to install this sensor. The length of these sensors are specified at time of order and standard sensors can range from 6 to 30 inches. PVC rod sensors can also be constructed to lengths up to 48 inches through the use of our LR7417 AutoCal sensor modules.
|
|
|
|
All pre-Smart Chip or push-botton calibrating display panels require an external AutoCal sensor module to be attached to the sensor rod (not pictured). Smart Chip enabled panels and our Ultra-8 display panel can use the rod pictured with new internal sensor circuitry.
|
|
|
|
|
| Bilge Buddy Bilge Pump Control |
 |
|
|
Our Bilge Buddy bilge pump control is a reliable alternative to float-based pump controllers currently common in the marine industry. By taking advantage of our capacitive sensing technology it is be free of moving parts that can be blocked by debris floating in the bilge.
|
|
|
|
By utilizing 2 separate sensors for empty and full, this innovative product allows the user to set where the bilge pump is activated and deactivated. These 2 setpoints help prevent rapid pump cycling in small bilge compartments and more complete bilge pumpouts.
|
|
|
|
Pat. Pending.
|
|
|
